1220 Uni. Grinder
Model 1018 Uni. on 90" cabinet
Model 1220 Uni.
SURFACE FINISH - Three quarter RMS to two RMS in hard steels and carbide to four RMS in soft steels.
IN-FEED SYSTEM - is of dove tailed design with long bearing surface. Pinion and hand wheel shaft is of tool steel supported by 0 Timken bearings. Rack is 14-pitch hobbed from solid with 20-degree pressure angle. Worm is hardened, ground and mated to 660 bronze gear. Hand wheel graduations are .00025. Slow in-feed optional.
WHEELHEAD SPINDLE - is double taper design, 2-1/8 diameter, High Speed Steel, hardened and ground and running in bronze bearings. Cones are adjusted by removing dust cover and turning nut to right pulling taper cones together and setting end play with Dial Indicator measurement to less than .0001. The Wheelhead is advanced by D2, 14 pitch rack, pinion gear and bronze gear, 5 pitch worm, hardened and ground and supported on tool steel shaft with end thrust being taken up by two (2) Zero Timken bearings.
WHEELHEAD - is equipped with lead weight assembly to eliminate backlash. Has High Carbon High Chrome Ways and one shot oiling system. Wheelhead swivels 360 degrees.
HEADSTOCK SPINDLE - is 2-3/4 diameter, double taper bearing design with Crystal Lake Number 7 taper, carbide or high speed steel centers. High-speed steel is used in Spindles requiring a guaranteed Spindle Nose roundness guaranteed from .000025 to .000005 at an additional cost. Spindle Nose is one degree taper for holding chuck or dead center driver. Headstock is arranged for Number 5C collet up to 1.
TAILSTOCK - Spindle is of D2 steel, hardened and ground, closely fitted to bore giving tremendous rigidity without loss of sensitivity to spindle. Center is Crystal Lake Number 7 taper, carbide tipped or High Speed Steel. Dust cap holds spring, can be adjusted for tension. Hole through spindle for center knockout.
DEAD CENTER DRIVER - on Headstock is a Ball Bearing design using standard ball bearings. The taper sleeve does not revolve, but the bearing revolves in its own race making, if necessary, replacement of bearing an easy operation.
HEADSTOCK AND TAILSTOCK - are bored in pairs and aligned the Compensating Table, which is V and Flat design and swivels six (6) degrees either side of center. Headstock swivels 360 degrees.
TABLE - is of V and Flat design mated to heavy base casting. Primary gears are helical cut wide face, having two (2) teeth in mesh. Secondary gears are wide face, spur, and 12 pitch. Pinions run in ball bearings and gears run in oil.
BASE CASTING - are extra heavy to dampen vibration for longer wheel life so necessary when using diamond and Borazon wheels. Tables are of ample length and weight for high finish without sensitivity. For example: The grinding of sides of control valves.
MOTOR DRIVE - is self-contained and is mounted on heavy vibration dampening cabinet with two motor drive arrangement. Headstock is equipped with 1½ hp DC Drive. Wheelhead on Model 1018 is powered by 3 hp AC Motor standard (DC Motor Optional). Wheelhead on Model 1220 is powered by a 5 hp AC Motor standard (DC Motor Optional).
COOLANT SYSTEM - over thirty-gallon capacity is self-contained in cabinet. Pump, with baffle plates, is rubber mounted on top of cabinet in the left-hand corner. (Over forty-gallon capacity coolant system on 90" cabinet models)
AUTOMATIC TABLE FEED -- has 1800 to one range Servo Drive Motor, rubber mounted, belt drive and connected to 200 to one gear reduction unit. Bull gear is steel, ¾ wide, 12 pitch, 14-1/2 degree pressure angle. Helical gears are iron, 14 pitch, 20-degree pressure angle, and 16-degree angle. Spur gears are steel, 14 pitch; 20-degree pressure angle all supported by large double or triple ball bearings. Gears dip in oil reservoir for smooth running.
INTERNAL ATTACHMENT OR COMBINATION OLD./I.D. GRINDING ASSEMBLY - Have their own drive motor for angle grinding or for production run. The 15,000 RPM (other RPM available) Combination O.D./I.D. Grinding Assembly mounts at the Wheelhead location.
The Internal Attachment is easily exchanged with the Wheelhead when desired or can be mounted at factory as an ID Grinder only.
The Combination O.D./I.D. Grinding Assembly can be switched from O.D. grinding to I.D. grinding by removing the belt from the O.D. Drive motor. Loosen 2 socket-head clamp screws pivoting the assembly to desired I.D. grinding position and securing clamp screws.
To revert back to O.D. Grinding simply reverse the procedure.
Quill sizes are available in 1/8, 3/16, or ¼.
RADIUS WHEEL DRESSER - has an adjustable height of 4 to 7-1/2 above the table with two (2) holders for diamonds. This dresser has been designed primarily for use on Crystal Lake Cylindrical Grinders. Units are adapted with solid angle ramp. Will dress both external and internal wheels. Includes base to fit Crystal Lake Grinder, adjustable up to 12 diameter wheel radii and angle dresser with carrying case and approximately 1/3 ct. Natural Chisel Shaped Roughing Diamond.
MEASURING EQUIPMENT - either electronic or air if applicable to mounting and customer choice. The equipment is subject to PRICE AT TIME OF DELIVERY FROM THE MANUFACTURE.
POSITIVE STOP - can be mounted on hand wheel for repeatability in sizing within .000020.
FILTER SYSTEM - is mounted inside of cabinet.
Send mail to email@example.com with
questions or comments about this web site.